BLACK FRIDAY SALES ACTIVE! NO BACKORDERS, IN STOCK INVENTORY ONLY! LIMITED QUANTITIES!

MPI MKIII 6V (Adjustable) Voltage Regulator
Share    Share this on Facebook!   Share this on Twitter

MPI MKIII 6V (Adjustable) Voltage Regulator

In Stock
 
$24.95
 
Item# (MPIR6VNEW)

 

  • Overview

Inline voltage regulator. For receivers or ignitions. If your servos or ignition requires 4.8v, use the 5.4v regulator. 4.8v battery packs are at 5.4v when fully charged and this gives a large margin of safety and a little more power (at less cost) than the 4.8v reg. The 6v regulator offers more power to the servos for higher speeds and more torque. Use 6v for DA and C&H ignitions.
It can take 5 amps continuous and 10 amps max.

For 100cc and smaller planes.

22ga wire

0.6 oz

  • Large heat sink for optimum performance
  • Dual HD AWG22 input/ouput connectors to double current capacity and redundancy
  • Output is factory preset to 5.95V, fully adjustable between 5V to 6.5V
  •  When input is higher than 6V or any set voltage, it will regulate to 6V or any set voltage
  •  When input drops below preset voltage, regulator is bypassed
  •  Weighs only 1.4 oz
  • Current: At 7.4V input, 10Amp continuous, 20Amp max for 1 minute
  •  Input Range: 4.8V -12V

    Note: Current capacity drops as input voltage increases



The new ones have two connectors on the input and output side. It was designed to share the load since these RC connectors are good for 5A continuous. If customer wants to plug two battery packs to the input side, it is OK. But, the two packs has to be identical packs - same brand, capacity, and voltage, and in same charging status. There is NO isolation between the two packs so both packs will be drawn simultaneously. This is NOT a battery back up.

  • Large heat sink for optimum performance
  • Dual HD AWG22 input/ouput connectors to double current capacity and redundancy
  • Output is factory preset to 5.95V, fully adjustable between 5V to 6.5V
  •  When input is higher than 6V or any set voltage, it will regulate to 6V or any set voltage
  •  When input drops below preset voltage, regulator is bypassed
  •  Weighs only 1.4 oz
  • Current: At 7.4V input, 10Amp continuous, 20Amp max for 1 minute
  •  Input Range: 4.8V -12V

    Note: Current capacity drops as input voltage increases

 

 

Required and/or Related Items

Photo Description Stock Price Buy
Down and Locked formerly WRC Wike R/C Products Miracle Switch 15A with Voltage Regulator and Charging Jack Switch
Down and Locked formerly WRC Wike R/C Products Miracle Switch 15A with Voltage Regulator and Charging Jack Switch
In Stock
$29.95
(WRCMSWITCH)





Allied countries of the United States regarding shipment of any products from TBM

WARNING - Gasoline and Turbine powered R/C model aircraft are not manufactured to withstand unlimited G's. Any R/C model aircraft can fail, be it a wing folding up or a fuselage breaking in half under too high of a load. Just as any full size aircraft, model R/C aircraft have a maximum G rating. Because you are not in the plane flying it and experiencing the G's and reading the G-meter, it is more difficult to judge the G's on the aircraft, and it is very easy to exceed the limits of the aircraft. Understand that if you perform a snap roll, parachute, wall, blender, knife edge loop, or pull hard on the elevator at almost any speed, you can be putting in excess of 15 G's, even in excess of 30 G's, and most aircraft can only designed to take 10-12 G's. If you perform any violent maneuver, you can break your plane. When I perform hard maneuvers, especially for the first time on an airframe, I am prepared for a failure and am prepared for it as best I can be. This mainly includes performing the maneuver far enough away from spectators that in event of a failure that I am not endangering others. In addition, be prepared for the manufacturer to not pay for a new airframe which is broken during flight. It is common practice for any manufacturer to not replace an airframe which breaks in the air or upon landing. I have only seen manufacturers replace airframes when they have received many of the same failures and the manufacturer determines that there was a design or manufacturing error. If you break an airframe, and you are the only one to do so, then it is probably not the fault of the manufacturer. Please fly safely, and avoid full throttle operation other than at low airspeeds.

R/C model jets, warbirds, aerobatic planes, DJI S1000 Octocopter, and UAV Unmanned Aerial Vehicles to name a few are not a toy! If misused, it can cause serious bodily harm and property damage. Fly only in open areas, and AMA (Academy of Model Aeronautics) approved flying sites. Follow all manufacturer instructions included with your plane, radio, servo's, batteries and engine. Aircraft manufacturers guarantees each kit to be free from defects in both material and workmanship at the date of purchase. This warranty does not cover any component assembled by the customer. All parts of high stress must be inspected and reinforced if necessary by a competent builder. Some parts should be glued again. High stress areas such as firewalls, motor boxes, wing mounts, landing gear mounts, etc., are areas of high concern. Seek help if necessary. In not case shall TBM be liable for the cost of any product it offers which is not manufactured by TBM. The liability to the manufacturer cannot exceed the original cost of the purchased item. Further, TBM reserves the right to change or modify this warranty without notice. In that TBM has no control over the final assembly or materials used for final assembly, no liability shall be assumed nor accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user assembled product, the user accepts all resulting liability. The kit manufacturers have provided you with a top quality, thoroughly tested kit and instructions, but ultimately the quality and fly ability of your finished model depends on how you build it; therefore, we cannot in any way guarantee the performance of your completed model, and no representations are expressed or implied as to the performance or safety of your completed model. It is the user's responsibility to inspect each component for worthiness.